SuperChevy.com has a wonderful article featuring the Dynamat Xtreme custom cut kit for thier C3 Corvette build.  Read the article to see how easy and fast it is to install Dynamat Xtreme custom cut kit for your next project. We have already done the hard work for you, just install in your project car and enjoy the benefits of the Dynamat experience.

http://www.superchevy.com/how-to/interior/1809-dynamat-custom-cut-insulation-for-your-c3-corvette/

HR-NETWORK-SROP600
We’d normally install insulation in a project car once all the paint is completed, but in an effort to keep stories coming we decided to paint the top half of the wagon thanks to Chopit Kustom, (714) 226-0860, and all the interior and the firewall, so we could install a headliner, glass, and start building up the interior and dash, as well as drop in the engine and trans. Before any interior trim or the headliner could go in, we covered all the sheetmetal that would be hidden under carpet or headliner with Dynamat. This is a lightweight elastomeric butyl and aluminum constrained-layer vibration damper, which serves to reduce road noise and “tin can” drumming that can occur with large, undampened metal panels. Read Full Article Here

Xtreme Trunk Kit Angle Square No BackDynamat Xtreme Trunk Kit
Today’s powerful subwoofers cause a vehicle’s trunk to flex and vibrate, which creates bass distortion, a reduction in maximum bass output, and poor sound quality. Some people may find trunk rattles cool, but it is actually just bad bass. If you really want to impress, install the Dynamat Xtreme Trunk Kit and show how you can pump clean, clear, crisp bass without the rattle.

When it comes to playing loud bass in a vehicle, it is all about Sound Pressure Level (SPL). Low SPL results when your subwoofer causes vibration and movement of your vehicle’s body panels. Installing the Dynamat Xtreme Trunk Kit will convert that vibration and noise into silent energy, which results in higher SPL. Tests have shown that installing the Dynamat Xtreme Trunk Kit is like adding an extra amp. The Trunk Kit is not just for coupes and sedans. Use it to treat the back walls and side panels of trucks, and the rear cargo area of small hatchbacks and SUVs. With the Dynamat Xtreme Trunk Kit, you get the tightest, loudest bass your subwoofer can produce.

For best results when installing, be sure to use a Dynamat Roller, and hear the Dynamat difference.

SKU: 19405
Contents: (5) 18″x 32″ (457mm x 812mm) pieces of Dynamat Xtreme Total Coverage: 20 ft² (1.85 m²)

Xtreme Speaker Kit Front No BackDynamat Xtreme Speaker Kit
Even the best new speakers cause speaker panel distortion.   Home audio speakers typically come in well crafted, heavy boxes to eliminate this distortion – a solution that is impossible (or at least impractical) in your car. For your car, Dynamat is the solution. Applying Dynamat to the panels surrounding your speakers eliminates speaker panel distortion by transforming the flimsy sheet metal into a solid non-resonant baffle. Dynamat improves mid-bass performance and stops vibration rattles and squeaks. Your stereo will sound its very best with Dynamat.

Kit contains two 10″ x 10″ pieces of self-adhesive Dynamat Xtreme to be used when mounting your speaker to a metal baffle like a car door or rear deck lid. For proper installation, use one of our Dynaroller tools.

SKU: 10415
Contents: (2) 10″x10″ (254mm x 254mm) pieces of Dynamat Xtreme. Total Coverage: 1.4 ft² (0.13 m²). Self-adhesive.

Xtreme Door Kit Front No BackDynamat Xtreme Door Kit
When driving, the body panels of your vehicle vibrate and create noise. The faster you drive, the louder that noise will be. At 70 mph, a typical automotive noise level reaches 85 dB. This will interfere with the sounds inside your vehicle, like your stereo, cell phone calls and conversations by affecting the dynamic range of these sounds. If you want your music louder, you can turn up your stereo, but that only increases volume. It does not give you back the dynamic range you have lost. One of the main culprits of this noise is your vehicle’s doors. Without Dynamat Xtreme, vibrations resonate and echo through the hollow inner door cavity.

Since much of the noise that comes from the road enters through the doors, installing the Dynamat Xtreme Door Kit creates a sonic barrier that converts noise-causing vibration into silent energy. By reducing the road noise, the Dynamat Xtreme Door Kit can increase the dynamic range of the sounds in your car, which can effectively double your vehicle’s amplifying power! You get louder sound from your car’s audio and less annoying noise from outside your vehicle.

The Dynamat Xtreme Door Kit does not require any special equipment, so it is very simple to cut and install. It will conform easily to your vehicle’s inner and outer door skins, and the sticky butyl rubber will adhere and stay in place without any special surface prep. For best results, install the Dynamat Xtreme Door Kit with one of our Dynamat roller tools. Use the Dynamat Xtreme Door Kit on your doors to hear the Dynamat difference.

SKU: 10435
Contents: (4) 12″ x 36″ (305mm x 914mm) pieces of Dynamat Xtreme. Kit includes enough material for two standard size doors. For proper installation, use one of our Dynaroller tools. Self-adhesive.


Dynamat, Inc. 3042 Symmes Road | Hamilton, OH 45015 USA | P: (513) 860-5094 | F: (513) 860-5095